RP Photonics

Encyclopedia … combined with a great Buyer's Guide!


Photoelectric Effect

Definition: the emission or excitation of electric carriers related to the absorption of light

Alternative term: photoemission

German: photoelektrischer Effekt

Category: physical foundations

How to cite the article; suggest additional literature

The operation principles of many types of photodetectors – e.g. photodiodes, phototransistors, phototubes and CCD or CMOS image sensors – are based on the photoelectric effect. This actually comes in two quite different forms: the external and internal photoelectric effect.

External Photoelectric Effect

If light with a sufficiently high photon energy hits a metal surface, for example, some of the light may be absorbed, and electrons are emitted from the surface. If the metal part (called a photocathode) is kept in vacuum and an electric field is applied using a second electrode (the anode), which attracts those electrons, one can detect a photocurrent, which is proportional to the incident light intensity. The external photoelectric effect provides the working principle of a vacuum phototube. Here, external means that the electrons are obtained outside the material from which they have been released.

That form of photoelectric effect found substantial attention by Albert Einstein and others in the early 20th century. It had been observed that the photoelectric effect occurs only for light with wavelengths below a certain limit, depending on the material; for longer wavelengths, even rather high optical intensities cannot give rise to that effect. Another observation was that the energy of the obtained photoelectrons (measured via a required stopping potential) depends on the optical wavelength: the shorter the wavelength, the higher the photoelectron energy, while the light intensity only affects the rate of photoelectrons emission. Those observations, which were hard to reconcile with classical electromagnetic theory, led to the idea that light energy is delivered in the form of small packages, which have later been named photons. They thus contributed to the early development of quantum mechanics and quantum optics.

The photon model well explains the mentioned observations. Only if a photon has a sufficiently high energy, it can trigger the emission of a photoelectrons – a process which requires a certain energy, namely the binding energy plus the resulting kinetic energy of the electron.

The external photoelectric effect is utilized in vacuum tube photodetectors, in particular in phototubes and photomultiplier tubes.

Internal Photoelectric Effect

The internal photoelectric effect does not produce photoelectrons which are observable outside the material, but only excites electrons to higher levels, namely from the valence band to the conduction band in a semiconductor material. A consequence of that is that a photocurrent is usually detected in a reverse-biased p–n junction or p–i–n junction. For explanations on the latter case, see the article on p–i–n photodiodes. There are also metal–semiconductor–metal photodetectors, where a Schottky junction is used.

The internal photoelectric effect is exploited in various types of semiconductor photodetectors, namely in photodiodes and phototransistors. Its precondition is that the photon energy is larger than the band gap energy of the material in the active region. While the bandgap energy of typical dielectrics like silica or other optical glasses is substantially too large, and also the carrier lifetime would be too short, various semiconductors exhibit a suitably small bandgap energy. For example, silicon-based detectors can work with wavelengths up to roughly 1.1 μm, although the responsivity often drops substantially above 1 μm. Materials with still lower bandgap energy allow photodetection at longer wavelengths – for example, indium gallium arsenide (InGaAs) up to ≈1.7 μm.

There are even materials for the detection of mid-infrared light, e.g. in infrared cameras. Their bandgap energy is so small that substantial thermal excitation occurs already at room temperature. To avoid that, such detectors need to be operated at substantially lower temperatures, e.g. using a Stirling cooler.

See also: photodetectors, photodiodes, phototransistors, phototubes, image sensors
and other articles in the category physical foundations

How do you rate this article?

Click here to send us your feedback!

Your general impression: don't know poor satisfactory good excellent
Technical quality: don't know poor satisfactory good excellent
Usefulness: don't know poor satisfactory good excellent
Readability: don't know poor satisfactory good excellent

Found any errors? Suggestions for improvements? Do you know a better web page on this topic?

Spam protection: (enter the value of 5 + 8 in this field!)

If you want a response, you may leave your e-mail address in the comments field, or directly send an e-mail.

If you enter any personal data, this implies that you agree with storing it; we will use it only for the purpose of improving our website and possibly giving you a response; see also our declaration of data privacy.

If you like our website, you may also want to get our newsletters!

If you like this article, share it with your friends and colleagues, e.g. via social media: